Find all your DIY electronics in the MakerShed. 3D Printing, Kits, Arduino, Raspberry Pi, Books & more!

AAA_powered_Arduino.jpg
MAKE Flickr Pool member Funax made an Arduino-compatible board powered by a single AAA battery.
A step-up converter is used to boost the battery’s 1.5V output to 5V and meet Arduino’s minimum power requirements. Keep in mind – this circuit would considerably reduce current supplied to the board and therefore limit its ability to power external components.

AAArduino on Flickr- Link
Learn more about DC-DC converters on Jaycar.com – Link

Related:
Uduino
Uduino – Low cost Arduino development boardLink

Arduino
Arduino @ MAKE – Link

Collin Cunningham

Born, drew a lot, made video, made music on 4-track, then computer, more songwriting, met future wife, went to art school for video major, made websites, toured in a band, worked as web media tech, discovered electronics, taught myself electronics, blogged about DIY electronics, made web videos about electronics and made music for them … and I still do!


Related

Comments

  1. nullobject says:

    This looks really cool, kudos to Funax for building such a good looking prototype. But isn’t this Make blog? I want to read about things I can learn to make…not just look at pretty pictures.

  2. The Oracle says:

    I tend to agree nullobject, that is pretty interesting, but as a whole the post is like the original Arduino just linking back to the Atmel datasheet and saying go ahead, build one.

    Just out of curiousity since it’s not at all evident, is the chip itself generating the oscillations for the buck regulator?

    And for the rest of us, http://www.sparkfun.com/commerce/product_info.php?products_id=8248

  3. MakeFan says:

    Any word on runtime length?

    AAA’s are pretty low power batteries, plus you have voltage converter loss.

  4. The Oracle says:

    The converter is around 85% efficient so losses aren’t bad. AAA’s will give you close to an amp-hour at 1.5 volts, the MCU with no LEDs or such draws at most a few mA.

    Overall, it is a practical solution. I’d like to get a handful of those boost regulators, I found the company site and datasheets, but none of the usual sources (like mouser and digikey) stock them.

  5. todbot says:

    Yup, AAAs put out about 1000 milliamp-hours (mAh). The converter gives 85% efficiency, so effectively 850 mAh. The AVR ATmega168 in an Arduino draws max about 20 mA when active. That means an AAA would let an Arduino last about 850mAh/20mA = 42 hours (at best). Of course, if you drive an LED at max brightness, it also consumes 20mA, so your lifetime goes down to about 21 hours.

    Of course, if you were really power conscious, you’d use PWM on the LED and some of the various sleep modes to extend the lifetime to weeks or months.

  6. MakeFan says:

    Todbot,

    Your calculations omit voltage. Your capacity is 850mAh at 1.5V. Yet your demand is 20mA at 5V. Doesn’t that mean your calculations are off by a factor of 3?

  7. todbot says:

    Yup, you’re right, I spazzed. The “efficiency” of the converter is really power or energy conversion efficiency. Power is in Watts, which is voltage*current. Energy is Watt-hours. The energy available in a AAA is 1.2V * 1000mAh = 1200 mWh. After conversion at 85% efficiency, that’s 1020 mWh. Since the converter is a 5V one, the available current capacity is 1020 mWh / 5V = 204 mAh.

    A shortcut to get to that number is to multiply the capacity of the battery times the effiency of the converter times the ratio of the voltage change:
    1000 mAh * 0.85 * (1.2V/5V) = 204 mAh

  8. MakeFan says:

    1.2V? Using rechargeables eh?

    Long story short you get about 10 hours (+-3 hours depending on battery type) of use. It would work nice as a backup if you’re working off a wall adapter.

  9. nawi says:

    hallo,tengkyu

  10. funax says:

    Hi,
    actual current at Vin of converter is 85mA (2 LEDs are active, 16MHz external xtal). I think the efficiency is

  11. tanjung says:

    Hi,
    Can i get the schematic one ?. It’s very interesting, and i want to build some…

    Thanks..

  12. acer says:

    GPRS and EGDE, both of which are class 10 are provided as
    are blue tooth and mini – USB. 0 is provided and offers excellent means of navigation around the functionality.

    Other connectivity options are available too, including a trio of
    USB 2. This is an Acer Laptop Review on the Acer AS1430Z-4677 which features a lightweight design at just a little over 3 pounds with excellent performance.

In the Maker Shed