DIY Open Source Inkjet Printer

DIY Open Source Inkjet Printer

The prototype design used a carriage assembly constructed from steel rods that were assembled using connectors that can be printed on an FDM machine. The entire carriage system is driven along the x-axis by a belt attached to a stepper motor. The print cartridge, taken from an HP point of sale printer, is driven along the y-axis by another stepper motor belt drive. The electronic controls use an Arduino Mega to run all of the printing systems.

The design resulted in a working prototype that fulfills all of the design constraints. The rod frame carriage design is lightweight, easy to assemble and easy to integrate with the other systems. The Arduino used in the electronics has a large library of resources available to perform things like LCD, SD card, and stepper control.
Areas where future work should be focused include making molds and casting printable parts to bring down the overall cost, developing host side software, and optimizing the speed.

Read the blog post and see the project’s Flickr set the Thingiverse thing.

[Via Dangerous Prototypes]

17 thoughts on “DIY Open Source Inkjet Printer

  1. Kyle Smeby says:

    I’ve been waiting for an open source hardware inkjet printer for a while now.  The Epson, HP, Brother, etc. cheap printer, expensive ink racket has to be brought to sanity.  I really hope this thing takes off.  Keep us posted if there is a kickstarter profile launched around this.

  2. Kyle Smeby says:

    I’ve been waiting for an open source hardware inkjet printer for a while now.  The Epson, HP, Brother, etc. cheap printer, expensive ink racket has to be brought to sanity.  I really hope this thing takes off.  Keep us posted if there is a kickstarter profile launched around this.

  3. Kyle Smeby says:

    I’ve been waiting for an open source hardware inkjet printer for a while now.  The Epson, HP, Brother, etc. cheap printer, expensive ink racket has to be brought to sanity.  I really hope this thing takes off.  Keep us posted if there is a kickstarter profile launched around this.

  4. Brandon Anello says:

    POS printers are thermal not inkjet – they use a thermal print head and a special heat sensitive paper. (try heating a receipt…)

    1. Anonymous says:

      Not all POS printers are thermal.  There are some which use this HP C6602A inkjet head.

  5. Brandon Anello says:

    POS printers are thermal not inkjet – they use a thermal print head and a special heat sensitive paper. (try heating a receipt…)

  6. Brandon Anello says:

    POS printers are thermal not inkjet – they use a thermal print head and a special heat sensitive paper. (try heating a receipt…)

  7. Anonymous says:

    Everyone is a hero, everyone has the opportunity to make a fortune, your blog well, I am very optimistic about you, then you can look forward to a good development. This is me,Mulberry outlet, and Mulberry bags there is a chance to look at, and holding to join in! ! !
    Mulberry factory shop

  8. Anonymous says:

    Everyone is a hero, everyone has the opportunity to make a fortune, your blog well, I am very optimistic about you, then you can look forward to a good development. This is me,Mulberry outlet, and Mulberry bags there is a chance to look at, and holding to join in! ! !
    Mulberry factory shop

  9. Anonymous says:

    Everyone is a hero, everyone has the opportunity to make a fortune, your blog well, I am very optimistic about you, then you can look forward to a good development. This is me,Mulberry outlet, and Mulberry bags there is a chance to look at, and holding to join in! ! !
    Mulberry factory shop

  10. Anonymous says:

    Everyone is a hero, everyone has the opportunity to make a fortune, your blog well, I am very optimistic about you, then you can look forward to a good development. This is me,Mulberry outlet, and Mulberry bags there is a chance to look at, and holding to join in! ! !
    Mulberry factory shop

  11. aaron teo says:

    I strongly support open source hardware and software. Great way to increase and share knowledge. 
    http://www.youshine.com.au 

  12. aaron teo says:

    I strongly support open source hardware and software. Great way to increase and share knowledge. 
    http://www.youshine.com.au 

  13. Jan says:

    would be more interesting to see an opensource printhead. but that sounds very complicated.

  14. Douglas says:

    I’m sick and tired of printer firm’s ink cartridge renewal ripoff. There must be a huge demand for a simple B&W printer capable of using generic handicrafts-shop bottled ink. I’d love to see a startup to give it a go. Most important?:

    o like emergency calls on your phone, you should ALWAYS be able to print B&W
    o no ink expiry.
    o no cartridge replacement, just ink refill

  15. John says:

    Just now hearing of this, three years later. This is great!

    Anyone know of any later projects? Maybe some which built upon this one, and improved it?

  16. Spearing the Bearded Clam says:

    also I would love to make one of these

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

My interests include writing, electronics, RPGs, scifi, hackers & hackerspaces, 3D printing, building sets & toys. @johnbaichtal nerdage.net

View more articles by John Baichtal

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK