How-To: Splice Wire to NASA Standards

Computers & Mobile Technology
How-To: Splice Wire to NASA Standards

Some commenters on my post about using a washer as a soldering aid noticed my sloppy splicing technique and were kind enough to educate me about the so-called “Western Union splice,” aka the “Lineman’s splice,” which is the preferred method for twisting solid-core wire leads together for inline electrical connections.

Developed during the heyday of the telegraph, the Lineman’s splice is designed for connections that will be under tension. It is commonly claimed that, properly made, a Lineman’s splice is stronger than the wires of which it is composed. In any case, it is a time-proven method, and, coolest of all, one of NASA’s Required Workmanship Standards. To wit, in a NASA-approved Lineman’s splice:

  1. The conductors shall be pre-tinned.
  2. There shall be at least 3 turns around each conductor and the wraps shall be tight with no gaps between adjacent turns.
  3. The wraps shall not overlap and the ends of the wrap shall be trimmed flush prior to soldering to prevent protruding ends.
  4. Conductors shall not overlap the insulation of the other wire.

Though the Lineman’s splice was originally used without solder, today soldering is common. And NASA insists on it:

  1. Solder shall wet all elements of the connection.
  2. The solder shall fillet between connection elements over the complete periphery
    of the connection.

This material comes from page 84 of NASA-STD 8739.4 (PDF), which is a great reference if you’re interested in best practices for interconnecting cables and wires. [Thanks, Alex Barclay!]

118 thoughts on “How-To: Splice Wire to NASA Standards

  1. jamesbx says:

    I read that NASA document years ago: it got me started using clear heat shrink tubing. Just have to remind myself to slide it on the wire before soldering.

    1. Travis says:

      I’ve made that mistake myself.

      I started using this method when doing auto electronics, but before I used heat shrink. It made insulating the wires with electrical tape much easier. Before, my tape would always slide off the end of the splice exposing the wires. But with this method, you can wrap each wire, and then bundle the whole group together and wrap the whole bundle neatly.

      I also found that if you are good at stripping the insulation off of the middle of a wire, this is a good method for making taps as well. Also you can splice more than 2 wires together by coiling 2 wires at the same time (I doubt that is up to NASA standards though).

  2. Avi Drissman says:

    What a badly-drawn picture. The wrappings on each side somehow reverse direction. They can’t end that way.

    1. jmin says:

      I’m glad I wasn’t the only one to notice.

      This must actually be an Escher splice.

      1. rocketguy1701 says:

        Ahh good, I’m not having a stroke after all…

      2. David Dean says:

        Likewise.

      3. Shadyman says:

        [neo] Whoa. [/neo]

    2. Robotblog says:

      I spent about two minutes staring at this, wondering what the heck was going on :P

    3. firstpres says:

      Really? You get all this good information and despite the visual typo, you still understood what was going on and despite all of the authors work, you had to nit pick? Just…wow.

    4. chb says:

      is this really the point?? its a fault yes – but you know how to do it :)!

  3. Mike says:

    Very M.C. Esher-esque.

    For those of us who are visual learners, these images are confusing. It would be difficult for those wire ends to terminate the way they do in the images. It looks like they reverse direction halfway through the twists.

    1. jeonlab says:

      Right. It’s like an optical illusion. The end of the right hand side of the twisted wire goes opposite direction. Interesting discovery!

      1. jeonlab says:

        actually both sides.

    2. Keith From Canada says:

      Actually, that drawing does show the correct wrapping direction. It is used for universal-law independent circuits like this one.

      1. darr247 says:

        Ha ha ha. Wiring up components that differ from what’s on the schematic is like ‘magic’, huh.

        1. keithfromcanada says:

          Actually, it is exactly like magic; stage magic, to be precise. He spent a lot of time preparing props that, when connected together, created an illusion that was ‘impossible’. (FWIW, he also fully explained how he did it.)

      2. tommy says:

        agreed… one twist, 4 wraps per side, solder… on to electronics

        1. tommy says:

          arrug… forgot the shrink wrap

    3. john says:

      wow!

  4. Josiah Ritchie says:

    A video of someone with skill doing this would help to understand how you do the wrappings efficiently and cleanly. How does this work with stranded wire or is that a different standard?

    1. rocketguy1701 says:

      There’s a whole category of when to use solid or stranded wire. I think you could use this splice if you had to with stranded, particularly if you make sure to twist the strands in the right direction (so they don’t loosen under tension).

      That said, I wouldn’t recommend using stranded in this application, for several reasons, but the one that leaps to the top is that a soldered connection subject to any sort of twisting or vibration will fatigue the strands at the end of the solder, leading to failure. Solid core is more resistant to that, if properly sized with reason.

      You can tin a stranded cable into a solid unit to avoid that at the splice, but you still have a solder interface farther away. So that only works if you’ve got either strain relief or no real strain in the first place (neither seems likely if you’re needing to use this splice). It’s less the tension, but the inevitable vibration that will slowly kill it.

      But then, I’m thinking in the mindset of the “it must not fail” school of engineering here. So YMMV.

    2. Keith From Canada says:

      It may not be a standard, but what I’ve always done with stranded wire was to spread the strands on both ends a bit, slip the two ‘tufts’ together (end to end) until the ends of the strands of one are almost touching the insulation of the other (trying to make sure that all of the strands are interspersed evenly), twist the whole thing until it is solid (pre-twist the wires in the opposite direction before joining to make the soldered connection lay flat), then solder into a solid unit. I’ve found that, in a pinch, if you strip off a lot of insulation, you can often get away with not using solder. Also, if you slice along the insulation instead of cutting it off, then wrap it back around the soldered joint, it adds mechanical support.

    3. darr247 says:

      The way to do it with stranded would be to separate all the strands so you can tin them individually, then twist them back together, do the splice, and when you finish with the final solder it will be the same as a solid wire splice, with no copper exposed anywhere in the connection to oxidize.

  5. johngineer says:

    At one of my old jobs I would have to do this type of splice on occasion. Handy tip: keep a thimble in your toolbox — it helps you avoid accidentally stabbing your fingers with the end of the wire.

    1. David Dean says:

      Interesting idea. I might throw one in the toolbox for smoothing down the ends of a wrap.

    2. arigger says:

      Hmm, my fingers are too fat for most thimbles… what about a copper end-cap?

      1. johngineer says:

        In a pinch I’ve used the metal cap from a whiskey bottle too :)

  6. Paul Wilson says:

    That drawing could use some correction. The direction of the turns does not match the orientation of the ends.

  7. rocketguy1701 says:

    Nice standards document! I’m not going to apply all of it to any of my projects(overkill, even for me), but some elements of it are very informative of what to be thinking about when doing a wiring harness (in my case likely an aircraft wiring harness which is a bit more critical than my other projects).

  8. Bryant Underwood says:

    This is based on a splice invented by Western Union to splice telegraph wires. Recall that in the 1800s there was the bare minimum of tools available. The splice was designed to not only be secure electrically but also mechanically. In addition the same cathodic affects that prevent corrosion in Wire-wrap assembly also protect this splice from corrosion.

  9. eric's tinger says:

    I still hate doing it with smaller wires…anything smaller than 20awg is just too much for my toe-fingers

  10. Keith From Canada says:

    FWIW, self-fusing silicone tape (e.g. F4 Tape, Rescue Tape, Miracle Wrap, etc.) makes high strength, well insulating, waterproof seals. To make sure that you are getting the good stuff (-65° C to 260° C, 700 PSI, 85 ppi, 400 v/mil (8,000 Volts/20mil)), check to see if it matches mil spec CID A-A-59163 and/or MIL-I-46862 Rev. C 02-98.

  11. Travis says:

    One of the first things I learned (or was at least taught) in soldering, especially in wire work. Was to always make a good solid mechanical connection first. The solder is there only for electrical connection.

    I have also found that this method puts less strain on the wire than when they are just twisted together, and is less likely to break.

    I have to admit, I still use less dependable connections when testing that are easier to disassemble.

  12. Jeff S. says:

    This is what I was taught in high school electronics, and still use to this day.

  13. Walt says:

    The example is good and it demonstrates a very strong splice. Thanks for making a note of it.

    There is a problem in your diagram at the far right end of the wire on the final twist. The direction of the wrap defies logic and physics unless you are like me, an admirer of art of M.C. Escher. Nevertheless, the concept is clear. It is fine as it is for us g-jobbers.

    Does that bug in the drawing really matter that much? Consider that a NASA or military SOP (standard operating procedure) may include or reference a picture or diagram similar to the one above for use by factory assembly staff and test/repair technicians. If the diagram above were included, that M.C. Escher twist on the final turn at the right end would become an expensive issue during an audit should verification or certification of a splice be required. QA inspectors in the DLA (Defense Logistics Agency) are required to compare an observation made during an inspection with a requirement of a standard. And as crazy as it sounds, that splice would be sited as defective and formally documented as a condition of noncompliance. Even if that inspector is intelligent (some aren’t) and realizes that the drawing has a bug, there is still a discrepancy that they will document. It is sad. I’ve been there. I’ve seen it happen. (Then there are all the stop-work forms, change authorizations, engineering analyses, change notices, re-certifications and so on once the problem is addressed . . .)

    (Man am I glad I don’t work in defense electronics anymore. :- )

    Anyway, your article will help others to make better repairs, even if they aren’t Escher fans. Thanks for publishing it.

  14. Sarge Misfit (@SargeMisfit) says:

    Is it just me, or are the ends in the 2nd picture the wrong way around?

    From the first picture and looking from center out on the 2nd picture, you see the wire coiling over the front from bottom to top. But the end is in the BACK from bottom to top.

  15. Ross Hershberger says:

    It’s easier to make this splice if you cross the wires at a 90 degree angle, with the insulated parts below and the stripped ends pointing up. Leave 2/3 of the stripped part above where it crosses. As the stripped part wraps around it gets much shorter so you need more length to wrap around the straight part. I had to do two of these today to repair a damaged power cord on a commercial wetvac. Solder and heat-shrink finished the job.

  16. aaron says:

    just looks like the farmer splice we use on pulse wire.

  17. Peter Barvoets says:

    Although not a “western union” splice, I always found the technique demonstrated here in the movie “The Train” by Burt Lancaster interesting.. http://youtu.be/Z8j9h4XYVTs

  18. 633squadron says:

    I usually splice stranded wire with Posi-Locks, or I use bullet connectors with shrink-wrap.

  19. Tim Courtland says:

    No wonder it took NASA so long to get to the moon… Lol

  20. Brian says:

    I recall someone (a post doc I worked with?) saying that the only way to get any work done on the scientific satellite their group was making was to come in at night while the NASA auditors weren’t around.

    “Is that the correct Philips-head screwdriver for that screw?”

    Might just have been a grad student war story, though.

  21. Jason Kumpf » How to Splice Wires to NASA’s Standards – How-To Geek says:

    […] NASA-STD 8739.4 – Crimping, Interconnecting Cables, Harnesses, and Wiring [via MAKE] […]

  22. How to Splice Wires to NASA’s Standards – How-To Geek » Ashton Technology Blog says:

    […] NASA-STD 8739.4 – Crimping, Interconnecting Cables, Harnesses, and Wiring [via MAKE] […]

  23. Superpants says:

    There is a whole document on aircraft wiring that gives loads of other useful tips;

    http://casa.gov.au/wcmswr/_assets/main/rules/1998casr/021/021c99.pdf

  24. Make Lehigh Valley :: This is a simple skill, but it looks like... says:

    […] This is a simple skill, but it looks like it would be a good one to pick up. Anyone know of some video of someone doing this?http://blog.makezine.com/2012/02/28/how-to-splice-wire-to-nasa-standards/ […]

  25. Filo elettrico Px ossidato says:

    […] parziale ecco il metodo consigliato dalla NASA per la saldatura degli spezzoni di fili: MAKE | How-To: Splice Wire to NASA Standards Non si sa mai hc ela tua Vespa un giorno decolli per lo spazzio :) Rispondi […]

  26. Bryan says:

    I learned to solder from a NASA instructor but not for certification. Learning to solder wires together tool like 6 weeks. Yes, this is one of the joints we learned

    The interesting part is why. Early on NASA was very unsuccessful in launching rockets. The failures were traced to “drum roll” …bad solder joints.

  27. 3/15 NASA’s Standards « physicalcomputing says:
  28. Radio help please - Page 2 - Dodge Cummins Diesel Forum says:

    […] is not possible. I always splice per NASA standards – never have a broken connection ever again! MAKE | How-To: Splice Wire to NASA Standards __________________ 2002 Ram 2500 – 4×4 […]

  29. Donne Brescia says:

    Thanks for the info, interesting idea.

  30. Are you NASA qualified? says:

    […] MAKE | How-To: Splice Wire to NASA Standards " No one gives a damn about the things I give a damn about The liberties that we can't do without seem to disappear like ghost in the air We don't even care, Until it vanishes away" Jason Isbell and the 400 Unit Reply With Quote […]

  31. How to splice wires together via NASA. | Tyler Merrick says:

    […] How-To: Splice Wire to NASA Standards Developed during the heydey of the telegraph, the Lineman’s splice is designed for connections that will be under tension. It is commonly claimed that, properly made, a Lineman’s splice is stronger…… […]

  32. Splicing Wire the NASA Way - SailNet Community says:

    […] in college, I ran across the lineman's splice technique and promptly forgot about it. I just ran across it again, as NASA uses it as their standard for solid wire. With a bunch more EE experience under my […]

  33. Wire Nuts? - Really? - Pelican Parts Technical BBS says:

    […] but sheeesh! try the western union splice it is used in aircraft so it should be ok for a car. MAKE | How-To: Splice Wire to NASA Standards __________________ Carrera S […]

  34. NASA Standard – good enough for me | Aquaponic DIY Automation Blog says:
  35. GMI Biomed Insights » NASA-grade soldering Guide says:

    […] How-To: Splice Wire to NASA Standards […]

  36. クロエ新作バッグ says:

    山梨 印鑑 クロエ新作バッグ http://rexuechuj.nikeoninsertjp.org/

  37. How-To: Splice Wire to NASA Standards – How To says:

    […] by GavChap [link] [46 […]

  38. nuipukawai says:

    Hmmm. Something about that middle illustration. That’s some fancy wire twistin’.

    1. Eric says:

      Yeah, it seems to be an Escher splice.

      1. John Wayne says:

        Or a Möbius splice ;)

    2. Pahchay says:

      Yes the right side starts out as “Overhand” but the end appears a bit “Underhanded” :-)

  39. How to Build an RGB LED Flashlight : My Creative Directory says:

    […] to the black wire from the toggle switch. If you are feeling adventurous you can try using the NASA style but I found a straight splice works just fine as […]

  40. Mikael Grøtan Hoseth says:

    I’ve always spliced that way… Never underestimate logic..

  41. J.R.Brillianton says:

    That has also been military standards, at least in the avionics field, for a very long time. Have to say that getting one to look as pretty as these illustrations would be a neat trick. The wire never wants to cooperate.

    1. John Wayne says:

      Part of A-School we were taught to splice and solder. I remember that wrap clearly to this day. It was the most challenging part of that class (that and avoiding getting hot blobs of solder in your eye – that happened to me).

      Actually, I think it might have been AFTA where we learned that – sort of like a secondary more advanced A school (Advanced First Term Avionics).

  42. James Bond Bond says:

    Great blogs buddy……… this will definitely assist me.Hook up wire

  43. MikeZP says:

    ok, now make list of all wire gauge and how much insulation should be taken away in each case

    1. Warren says:

      bet there’s a standard for it :)

  44. DrDaveLivIP says:

    I’ve made many Western Union splices, none of which looked like the illustrations. Of course I only work in three dimensions not four.

  45. Kbrauneis says:

    also… no mention of inserting heat schrink tube before begining to splice.

    1. John Wayne says:

      Ahahahaha – I’ve so DONE that! Looking at your beautiful solder job – nice and clean with not cold spots – lo and behold no shrink tubing. DOH!

      1. Ryan S. says:

        I’ve been scatterbrained enough to do that with connector hoods–D’oh indeed!!!!! :D

      2. Heinrich D. Bag says:

        That’s what E-Tape is for!

      3. brizad says:

        lolol

  46. Garagepunk says:

    “I am the lineman for the county”

  47. Tony Clark says:

    How does the wire start running counterclockwise and end with clockwise loop?

  48. Keep Wires Locked Together with the Linesman Splice - IT Clips says:

    […] to :58 in the video above to see how Linesman splice is done. According to Make, this splice is the preferred connection method of NASA. Here’s how they suggest doing it […]

  49. Mantenha Wires Bloqueadas Juntamente com o bandeirinha Splice | UnlockPWD.com says:

    […] para : 58 [1.999.011] no vídeo acima para ver como emenda Linesman é feito. De acordo com Faça , esta emenda é o método preferido de conexão NASA . Veja como eles sugiro fazê-lo […]

  50. Keep Wires Locked Together With The Linesman Splice | Lifehacker Australia says:

    […] to :58 in the video above to see how Linesman splice is done. According to Make, this splice is the preferred connection method of NASA. Here’s how they suggest doing it […]

  51. Wire replacement and wire nuts - Page 2 - SailNet Community says:

    […] to be soldered have to be wound up with a lineman's splice. Solder is just more or less a binder. How-To: Splice Wire to NASA Standards | Make: The problem with most wire splices is exactly like the one in your […]

  52. Charlie Wilson says:

    i am familiar with this splice, known to me as a western union splice . I used this splice many times over the years. But what I found interesting is that while I was in the Navy in the 60’s I was flying on P2V-7s patrol planes (anti-sub). We relied heavily on HF radios and Morse code. We had several antennas and one of those was a long wire trailing antenna, which was a very long piece of solid copper wire with a weight on the end, wound on a motor driven spool. When we used this antenna we would unlock the spool and the weight and gravity would pull the wire out behind the airplane. The weights and wires would sometimes break and require splicing. The method of splicing was to use a western union style of splice to splice two wires together and they added another piece of wire at the splice point and it was also spliced western union style into the splice. This was just a mechanical splice, not soldered. They seemed to be good splices because one time we were landing and I forgot to rewind the antenna so we landed with the long wire antenna weight bouncing down the runway and the weight never came off.

    1. John Daniels says:

      Very interesting story! Thanks for sharing!

  53. Aleksandar K. says:

    Ok the the wire starts looping one way and ends the other way round. Seriously bugging me.

    1. Richard Fantasimo says:

      Three long twists of the wires around each other, then take each end and do the three to four tight wraps of wire. Snip of the excess.

  54. GODSEND DC2 Log .... "dirty diana" - Page 10 - Team Integra Forums - Team Integra says:

    […] makes things much more reliable than just soldering tinned ends. The easy instructions are here: How-To: Splice Wire to NASA Standards | Make: __________________ My FS thread 95 EJ1 Milano RIP/died/sold -> 98 DB7 CSM RIP/totalled […]

  55. Richard Fantasimo says:

    Learned this in Electronics 1-2 in high-school. We were required to do examples of various splices and the proper amount of twists per splice. This was the hardest, but I managed to get mine looking exactly like this and can still do this today.

    Thank you Mr. Trujillo.

  56. Peter says:

    CAD Drawings do not always imitate the real world as evidenced in these pictures. The idea is otherwise portrayed flawlessly.

    In movies this is called suspension of disbelief !

  57. Heated Seats - Electrical - JeepForum.com says:

    […] I never use them and never will. I always revert to the NASA standard for connecting wires. https://makezine.com/2012/02/28/how-t…asa-standards/ __________________ '14 JK Sport, 6-sp. Lifted, mud-tires and a […]

  58. hamitron comments on "Raspberry Pi Zero Hidden in an Xbox Controller" - Exploding Ads says:
  59. How-To: Splice Wire to NASA Standards - DevOps Infographics Resource Center says:

    […] The source of this awesome design from makezine.com […]

  60. How-To: Splice Wire to NASA Standards - DevOps Infographics Resource Center says:

    […] The source of this magnificent infographic from makezine.com […]

  61. Een ouwe tang… (An old pair of pliers) | The Dutch Luthier says:

    […] The so-called “Lineman Splice” or “Western Union joint”. This knot is still used by NASA […]

  62. How to Build an RGB LED Flashlight – Your Smart IOT says:

    […] to the black wire from the toggle switch. If you are feeling adventurous you can try using the NASA style but I found a straight splice works just fine as […]

  63. Heather Waldie Galbreath says:

    NASA may have adopted it but they DID NOT invent it. I was a USAF Manufacturing Engineer and STS Operations Officer. This splice was invented for telegraph wires and the formal name is the “Western Union splice”. It has amazing tensile strength, and is nearly impossible to pull apart – the wire itself will usually fail first. The splice was then adopted by the fencing people when innumerable miles of wire were strung to contain livestock. An amazing patented little tool by the JL Behmer Corp. (http://www.jlbehmer.com/) makes the splice fast and easy and creates a perfect and tight splice (after a little practice. It is a must have if you mainteain wire fences (my wife uses to maintain 7 1/2 miles of fence). As part of the FAA tests to become an aircraft mechanic – you must demonstrate this splice and then test it to destruction – the wire should fail before the splice. sent by Terry Galbreath

  64. Antron Argaiv says:

    I’ve posted a scan of the Digital Equipment Corporation’s Workmanship Standards Manual to scribd. It’s got all kinds of chassis and PCB assembly tips in it, probably some cribbed from NASA.

  65. Standard Operating Procedures – thewatchdc says:
  66. Andrew Smalls says:

    The link to the PDF isn’t working for me… http://www.hq.nasa.gov/office/codeq/doctree/87394.pdf
    Has anyone been able to get it?

  67. Resist_Tyranny says:

    NASA is a bullshit factory. Screw those lying ba$tards

  68. NASA流はんだのワイヤー結び – 買い物タイム says:

    […] やり方は、写真の通です。 2つのワイヤーを均等の長さで交差させ、そこから他方のワイヤーに絡めて行きます。 そこにはんだ付けをすれば、完璧です。 情報元サイト […]

  69. Robert Alex Kiefer says:

    The link for the standard didn’t work for me. But, this one did: http://www.hq.nasa.gov/office/codeq/doctree/87394.htm.

    1. LisaNMartin says:

      Thank you. We’ve updated the link in the article.

  70. NoSleepAtAll.com says:

    I was Certified for mobile electric wiring back in the mid 90’s and Soldering a joint was a no no. The correct way was to us a crimp connection believe it or not?

    1. J Allen says:

      That’s an ongoing discussion/debate about reliability of joints in a high vibration environment.

      I’ve seen it argued both ways, and the industry has wandered around both directions as well.
      I believe Ford currently requires splices to be twisted together perpendicular to the wire run, and then folded down against the wiring before being covered with heat shrink or tape, but I may be mis-remembering the procedure.

  71. dwarsligger says:

    i like the baked potatoes …

  72. P0301 - Page 5 - NewBeetle.org Forums says:

    […] I personally solder wires together and use shrink tube (sometimes two layers) over that. I have a 100 watt soldering iron I use for this, as your typical 25 to 30 watt iron won't work well on heavier gauge wires used in a car. On very large connections (like 6 gauge wire to a copper ring terminal) I've used a plumbing torch to get the thing hot enough. I've heard some people say that soldered wire connections in a car can break over time due to vibration, but I've never had that happen to me. I have had crimped connections go bad due to corrosion, since most of those connectors aren't waterproof. If you're really paranoid, you can use a lineman's splice (and solder it), which is overkill, but designed to work in tension: How-To: Splice Wire to NASA Standards | Make: […]

  73. Biscuit says:

    Although this looks like a good rendition of the splice it has a significant visual flaw in the representation that could be confusing. According to the turn of the twist starting from the center of the splice the wire should be turning up from the bottom of the center wire on the right end and coming over the top on the left end. The visual makes it look as if the wire ends changed directions in the middle of the twist. It’s a small detail, but, it creates a little confusion.

  74. Makezine.Com promotes ham radio - KB6NU's Ham Radio Blog says:

    […] also has an article on this splice. I used the article when I spliced the 450 Ω ladder line for my Cobra doublet, but I think the […]

  75. ingenieurs marocains says:

    هيئة المهندسين التجمعيين – corps des ingenieurs du parti du RNI

    corps des ingenieurs du parti du RNI

  76. Ideas of the Week: Spring Board Clamping, Rubber Band Palms, and Why Additional Elements Equal Beer! | Make: | IMAGICLAY.COM says:

    […] in all our hottest posts right here on Make: is in regards to the lineman’s splice, a sturdy and strong approach of […]

  77. GRAMPA says:

    this method was used first bu the people that installed the telegraph system. I myself am one of the few electrical masters in Michigan who was trained under the different methods used when the knob and tube wiring were installed. many buildings in Detroit still have wiring operating from 1910 we had two basic methods used for concealed ans another used for surface. the lesson learned from this method of connection is when it works dont change it When I joined the navy and learned electronics this method was taught along with how to solder. I have seen connectons over one hundred twenty years with a solid connection without showing any resistance because I tested it

    Grampa~~~~~~Mullan Elect.

  78. Warren says:

    Wish I’d learned this years ago

    (You have your reference wrong, now, btw – it’s page 71, section 19.7. And the link to the doc should be https://standards.nasa.gov/standard/nasa/nasa-std-87394)

  79. starlord | chrcal says:

    (NASA) The Office of Safety and Mission Assurance Code Q website was decommissioned and replaced with sma.nasa.gov.
    Please update any bookmarks you have for the old site. Updated link to revised PDF NASA-STD-8739.4 is here:
    https://standards.nasa.gov/file/2615/download?token=jcZ-qz2k

  80. hahnster says:

    Father in-law worked at NASA (radio Engineer) taught me to use simple Lap Splice. Maybe something with RF ????? I have seen the lineman’s splice but never use it.

  81. 雕蟲絕技:跳板金箍棒、橡皮筋加巧手、多買一點零件換啤酒 – Make says:

    […] 扭線接線法 《MAKE》最受歡迎的文章莫過於扭線接線法(lineman’s […]

  82. Raspberry Pi projects part 1 – A working NES in just the controller | brain -> blueprint -> build says:

    […] If you want a power LED (a 5mm LED fits nicely set back into the hole left by the lead), also solder the -ive side of a LED to header pin 14 and the +ive side to pin 2, via the required resistor, feel free to splice to nasa standards! […]

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

I am descended from 5,000 generations of tool-using primates. Also, I went to college and stuff. I am a long-time contributor to MAKE magazine and makezine.com. My work has also appeared in ReadyMade, c't – Magazin für Computertechnik, and The Wall Street Journal.

View more articles by Sean Michael Ragan

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK