This project was inspired by Cooking for Geeks author Jeff Potter’s quick DIY sous-vide hack. My plan, initially, was to just hack the controller into an enclosure with an A/C outlet, the idea being that you could just plug any heater you wanted into the outlet.
Looking around for cheap temperature controllers, however, I happened across the STC-1000 on eBay for $25. It’s not PID, but it has proven to be accurate enough for almost any practical purpose. And since the STC-1000 has both heating and cooling functions built-in, the logical next step seemed to be to split a single A/C outlet so that you could plug a heater or a cooler (or both) into it and use it for all kinds of stuff.
The STC-1000 will regulate at any temperature between the freezing and boiling points of water, which opens up all kinds of potential applications in chemistry, aquaculture, zymurgy, hydroponics, cooking, etc., etc. And unlike most other water temperature controllers I’ve seen around, this one can operate in heat only, cool only, and heat-or-cool-as-necessary modes.
More:
40 thoughts on “Make: Projects – Water Bath Thermostat”
Comments are closed.
ADVERTISEMENT
Join Make: Community Today
I could build this and use it to cook individual servings of beef stew for lunches.
Sean, is the STC-1000 on eBay actually 120 VAC?
I see in the description section the seller mentions both 110V and 220VAC±10%, 50/60Hz
Dave
I think what the eBay sellers do is look at your mailing address and include the version of their controller that is appropriate for your national power system.
Sean, is the STC-1000 on eBay actually 120 VAC?
I see in the description section the seller mentions both 110V and 220VAC±10%, 50/60Hz
Dave
While I like the idea of a inexpensive temperature controller the STC-1000 does not seem to have a food grade probe. Depending on what you want to do this could put you back in the market for a $60 open hardware temperature controller kit that does heating/cooling and includes the stainless steel food grade probe.
http://screwdecaf.cx/yatc.html
The STC-1000 uses an NTC thermistor temperature probe. I am in the process of taking the necessary measurements to determine its K value, at which point it should be possible to buy an aftermarket food-grade stainless thermistor probe that will work with the STC-1000, if it is necessary for your application.
The STC-1000 uses an NTC thermistor temperature probe. I am in the process of taking the necessary measurements to determine its K value, at which point it should be possible to buy an aftermarket food-grade stainless thermistor probe that will work with the STC-1000, if it is necessary for your application.
Did the author do this so we can use aftermarket SS probe or at least a replacement? Thanks.
While I like the idea of a inexpensive temperature controller the STC-1000 does not seem to have a food grade probe. Depending on what you want to do this could put you back in the market for a $60 open hardware temperature controller kit that does heating/cooling and includes the stainless steel food grade probe.
http://screwdecaf.cx/yatc.html
While I like the idea of a inexpensive temperature controller the STC-1000 does not seem to have a food grade probe. Depending on what you want to do this could put you back in the market for a $60 open hardware temperature controller kit that does heating/cooling and includes the stainless steel food grade probe.
http://screwdecaf.cx/yatc.html
So how does the performance of this compare to a PID approach? Anyone know just how this is different?
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
PID uses an algorithm to prevent temp overshoot and undershoot. This rig simply turns the outlet off when the target temp is reached. I tested my rig out last night and since my crock pot has a slow temperature response it overshot by about 2 degrees. If I had a PID on it and calibrated it, it would know to turn the outlet off (or start pulsing it) before the target temp was reached to compensate.
So how does the performance of this compare to a PID approach? Anyone know just how this is different?
So how does the performance of this compare to a PID approach? Anyone know just how this is different?
Is the thermistor that comes with the STC-1000 waterproof?