Flashback: Living Air Plant Brooch

Craft & Design Gardening Home
Flashback: Living Air Plant Brooch

air_plant_brooch_title_photo

By Haley Pierson-Cox

From terrarium necklaces to moss rings, living jewelry is popping up just about everywhere. Are you ready to get in on the plant-wearing trend? Make your own unique, green pieces with my air plant brooch tutorial!

Materials

Wood scrap at least 2" wide by 2" tall, and ¼" thick
Fine tip permanent markers, red and black
Pencil
Embroidery floss 48" length
Pin back 1" length
Jewelry adhesive I used Amazing GOOP Craft Arte
Embroidery scissors
Wood oil
Cloth rag
Sandpaper fine grain
Drill with 5/64" drill bit
Handsaw
Spring clamp
Ruler
Safety glasses
Face mask
1 small air plant

Directions

air_plant_brooch_tutorial_01.jpg

Step 1: Put on your safety glasses and facemask, then select a piece of scrap wood. If needed, use your handsaw to cut it to size, making sure that the thickness of the piece is a uniform ¼".

My father-in-law is a violin maker. I grabbed my piece of wood from his scrap bin, which is why it has a curved shape. As long as the thickness is uniform, your scrap can be any shape you’d like.

air_plant_brooch_tutorial_02.jpg

Step 2: Use the sandpaper to smooth away any rough spots or jagged edges on the wood.

air_plant_brooch_tutorial_03a.jpg

air_plant_brooch_tutorial_03b.jpg

Step 3: Holding the piece of wood securely with a clamp, measure ½" in from the right edge. Starting at the top, use the handsaw to saw a notch down to the center of the piece. Smooth away any rough edges with sandpaper.

Because my wooden piece is curved, my notch is only about ¼" deep. But if my shape had been square, the notch would have needed to be about 1″ deep to hit the center.

air_plant_brooch_tutorial_04a.jpg

air_plant_brooch_tutorial_04b.jpg

Step 4: Holding the piece of wood securely with a clamp, measure ½" in from the left
edge. Make a mark halfway down the height of the piece (this mark should line up with the bottom of your notch from Step 3). Using the mark as a guide, drill a hole all the way through the wood from front to back. Smooth away any rough edges with sandpaper.

air_plant_brooch_tutorial_05.jpg

Step 5: Using a cloth rag, apply a light coat of wood oil to the entire surface of the wooden piece, allowing the oil to soak in and dry before moving on to the next step.

air_plant_brooch_tutorial_06.jpg

Step 6: Carefully draw a heart design in the bottom right corner of the piece using black and red permanent markers. Once the ink has dried completely, use a cloth rag to apply an additional layer of wood oil to the entire surface of the wooden piece. Again, allow the oil to soak in and dry before moving on.

air_plant_brooch_tutorial_07.jpg

Step 7: Turn the wooden piece over. Using a strong jewelry adhesive, apply the pin back to the wood and allow it to dry completely.

Since this is a large brooch, the higher you place the pin back, the more stable it will be. For square wooden pieces, place the pin back near the top.

air_plant_brooch_tutorial_08a.jpg

air_plant_brooch_tutorial_08b.jpg

Step 8: Cut the embroidery floss into six 8" pieces, gathering them into a bunch and knotting one end. Separate the strands, doubling them up so you have 3 thick pieces, then braid the full length of the floss to create a braided cord. Do not knot off the second end.

air_plant_brooch_tutorial_09a.jpg

air_plant_brooch_tutorial_09b.jpg

Step 9: Thread the braided cord through the hole from back to front.

air_plant_brooch_tutorial_10a.jpg

air_plant_brooch_tutorial_10b.jpg

Step 10: The braided cord will gently hold the air plant in place. For it to work properly, it needs to be snug, but not so tight that it will damage the plant.

To get the right cord length, place the air plant on the front of the brooch, then wrap the cord around the plant, feeding the unknotted end through the notch you carved in Step 3. Starting on the back side of the notch, tug gently on the cord until the plant is held snugly in place, then use a marker to make a small dot on the cord just after the notch, marking the length. To finish, tie a knot at the mark you just made, then use scissors to trim off any excess floss after both knots.

air_plant_brooch_tutorial_final_02.jpg

You’re done! Strap in your air plant and rock your new living jewelry! (Just don’t forget to water your plant and return it to its window once in a while.)

About the Author:

Haley.jpg

Haley Pierson-Cox is a Brooklyn-based craft writer who loves granny glasses and loathes extraneous apostrophes. She blogs about crafts, cats, domestic bliss, and DIY goodness at The Zen of Making.

Discuss this article with the rest of the community on our Discord server!
Tagged

Haley Pierson-Cox from Red-Handled Scissors is a maker of crafts, a lover of cats, an avid swearing enthusiast, a cross-stitch book author, and a general purveyor of quirk. She's also sometimes an irritable cartoon named Tiny Cranky Haley. https://www.redhandledscissors.com

View more articles by Haley Pierson-Cox

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK