How-To: Corrugated Glow Tea Light Lantern

Home

CRAFT: Home Sweet Home
glow_HorizontalRailing.jpg
Corrugated Glow
Create sunset lighting with a fiberglass tea light lantern.
By Ross Orr

A friend of mine recently finished a deck remodel, whose highlight (literally) is a transparent corrugated roof that diffuses sunlight in a delightful way. This inspired me to find some way to continue that glow after sunset, in the form of a lantern illuminated by tea light candles.
There are many colors and styles of corrugated roofing available, and whole 8-foot sheets (Sequentia brand) are $23 at my local lumberyard — that’s enough material for up to 10 lanterns. The kind my friend used for the deck is fiberglass-reinforced plastic (FRP), which diffracts light with a sparkly halo. After some feverish experimenting with cut-off scraps, I eventually came up with the graceful lantern design shown here.
In the following steps, proceed carefully so you don’t crack the plastic, which is somewhat brittle.

Materials

Corrugated plastic sheeting 9½” of 26″-wide, should have 10 wavy ribs
¾” square pine or hardwood sticks 3′ per lantern
Galvanized all-purpose utility wire 12-gauge, 42″ per lantern
#8 truss-head screws ¾” long, 6 per lantern
Light gauge sheet metal
Clear tape or ¼” heat-shrink tubing
Tea light candle
Handsaw
120-grit fine sandpaper
Tin snips
Wire cutter or pliers with cutting notch
Drill and bits about 1″
Phillips screwdriver
Utility knife

Directions

glow_CutSheet.jpg
Step 1: Cut the sheet to size.
Mark a 9½” strip from the corrugated sheet, cutting across the ribs. This material is a bit too brittle to cut with a saw, but tin snips work well.
glow_Drill2.jpg
Step 2: Cut the uprights.
Cut 3 wooden sticks (uprights) 12″ long. Sand their sides and smooth sharp corners with 120-grit sandpaper. Measure 2″ from each end and drill crossways holes slightly larger than the wire you are using.
Step 3: Cut the wire to length.
Unroll several feet of wire, carefully unbending it before cutting. Cut 2 pieces 21″ long. Thread the wires through the holes in one of the wooden uprights until an equal length extends from each side. Bend the wires upward on both sides of the wood to form a “V” of about 60 degrees.
glow_PartTriangle.jpg
Step 4: Connect the uprights.
Thread the wires through the 2 holes of the next wooden upright. Slide the sticks together until there is 5¾” of wire between them. Make sure this spacing is correct, then twist the second stick and bend the wires going through it to form another “V.”
glow_Finished-Framework.jpg
Repeat with the third wooden upright. You should end up with a triangular framework where the free ends of the wire align, overlapping by about 1½”. The framework will probably be crooked at first; tweak the wire bends slightly until the frame is symmetrical and stands straight. Leave the free wire ends unattached for now.
Step 5: Attach the corrugated plastic.
Roll up the corrugated plastic into a tube, over-lapping the first and last ribs. This material is stiff enough that it will try to spring open again, so be careful! You may need an extra pair of hands here, or use packing tape, spring clips, etc., to keep the tube held together in the following step.
glow_Wrapped.jpg
Slip the wood/wire framework inside the corrugated plastic tube, with one upright behind the overlap. Make sure that the wood protrudes an equal distance beyond the plastic at each end. Adjust the rib overlap so it is snug and even from top to bottom, and then tightly hold the plastic and wood together.
glow_Drill-Fiberglass.jpg
With a drill bit slightly larger than your screw threads, drill holes 2″ from each edge of the plastic. (Don’t drill into the wood.) Drive the screws into the wood uprights, but don’t tighten them too much — stop when the head just begins to press against the plastic. Check that the other 2 uprights are straight within their ribs, and then finish the remaining holes and screws.

Quick Tip: Cutting plastic can leave ragged edges, which should be sanded lightly until smooth to the touch.

When drilling the screw holes, if you don’t have extra hands helping you, try holding the ends of the wood uprights between your knees for support as you’re drilling through the plastic and driving the screws. Or slip a length of 1x scrap wood (on edge) through the middle of the frame, and prop up its ends to support the work.

Step 6: Join the wire ends.
Now you can join the overlapping wire ends together. Wrapping them in clear tape works fine, but for a more finished look, I used ¼” heat-shrink tubing. (A wonderful craft material sold by electronics suppliers, this shrinks down to half of its original diameter when held over a flame.)
glow_CutTabs.jpg
Step 7: Make the candle base.
To make a platform for the candle, I cut a triangle from thin-gauge aluminum, although a coffee-can top works, too. Trace the outline of the candle in the center and mark 3 rectangular tabs within this circle. With a sharp utility knife, puncture the metal and cut 3 sides of the tabs, then fold them upward.
Make sure that the tabs will snugly grasp the sides of a tea light, even when held sideways. Corrugated plastic can catch fire if exposed to direct flame (which smells horrible!), so for safety’s sake, don’t skip this step.
glow_PlatformFold.jpg
Step 8: Attach the candle base.
Mark the locations of the wires on the underside of the platform. Use a straightedge to start bending each flap downward. Put the platform in place and finish wrapping the folded flaps around the wires to secure them.
glow_SnugCandle.jpg
Step 9: Enjoy the glow.
Flip the lantern right-side up again, snugly place your candle inside, and enjoy the glow.
glow-opener-HorizontalDeck.jpg
About the Author:
Ross Orr plays with fire in Ann Arbor, Michigan.

2 thoughts on “How-To: Corrugated Glow Tea Light Lantern

  1. Anne says:

    That is beautiful! I love how everything, even the screws, adds to the design.

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

I'm a word nerd who loves to geek out on how emerging technology affects the lexicon. I was an editor on the first 40 volumes of MAKE, and I love shining light on the incredible makers in our community. In particular, covering art is my passion — after all, art is the first thing most of us ever made. When not fawning over perfect word choices, I can be found on the nearest mountain, looking for untouched powder fields and ideal alpine lakes.

Contact me at snowgoli@gmail.com or via @snowgoli.

View more articles by Goli Mohammadi

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK