Find all your DIY electronics in the MakerShed. 3D Printing, Kits, Arduino, Raspberry Pi, Books & more!

banner_design_photography.gif
slidescan-finished3a.jpg
By Andrew Lewis
Preserving 35mm photos on a computer is a great way to keep them safe, and chances are that either you or someone you know has an old box of irreplaceable memories waiting to be scanned. The problem is that an ordinary scanner doesn’t really scan slides or negatives properly. The reason is that slides should be illuminated from behind, while conventional scanners are designed to capture reflected light from a document.
You could go out and buy a dedicated film scanner, but there is a much cheaper alternative if you already have a flatbed scanner or scanner/copier attached to your computer. A simple cardboard adapter can be used to capture the light from the scanner and reflect it behind the slide. Once the adapter is in place, you can scan the slide as though it were an ordinary document.


slidescan-youneed.jpg

Materials

A sheet of A4 (8 ½ x 11) thick, silver card stock
Downloadable template
, below
Scissors
Pencil
Ruler
Sticky tape

Download PDF Download the Template PDF
Right click to save the PDF to your desktop. Directions on downloading PDFs.


Directions

slidescan-step1.jpg
Step 1: Take a piece of silver card stock and download and print out the paper template on the plain (non-silver) side.
slidescan-step2.jpg
Step 2: Cut around this shape with the scissors and fold the triangular wings upright so that the shiny sides of the card stock face each other.
slidescan-step3.jpg
Step 3: Now fold the longest part of the rectangle in to touch the edges of the triangles, so that the whole thing resembles an open-bottomed, triangular wedge with the shiny side of the card stock to the inside.
slidescan-step4.jpg
Step 4: Tape the corners of the adapter together, and it’s ready to use!
slidescan-finished 2.jpg
To use the adapter, place a slide or negative onto the scanner, and then place the adapter over the top. For the best results, line up one side of the slide with the center of the adapter. Leave the lid of the scanner open. If your scans have an uneven brightness, try adding a thin piece of tissue paper between the slide and the adapter. The tissue will diffuse the light and stop the scanner from seeing the space behind the slide of the slide.
Take a preview scan with your favorite image editor and crop the scan to area of the slide. The higher the resolution at which you scan, the more detail you will get. I recommend setting the scanner to at least 1200 DPI.
slidescan-finished1.jpg
If you are scanning negatives, you need to perform a little bit of additional computer jiggery-pokery to reverse the color of the slides. Most image processing programs will have an ‘invert’ function that will reverse the colors for you, including Microsoft Paint. You might also want to adjust the brightness and contrast of the slides to make them look better on the screen.
You will probably notice that there are a few specks of dust on your slides when you scan them in. This is usually unavoidable, but a soft lens brush or a clean makeup brush can help minimize the problem. To remove any persistent specks or scratches, you can use a photo editor with a heal tool. If you don’t have a program that can do this, you can download GIMP or Paint.net for free.
slidescan-finished3.jpg
This image shows the raw scan on the left, the inverted scan in the middle, and the final image with the scratches and dust removed on the right. The entire process took less than 10 minutes to complete.
CZ_MakeProjects.gif


About the Author:
author_andrew_lewis.jpg
Andrew Lewis is a journalist, a maker, victophile, and founder of the www.upcraft.it blog.

DG


Related

Comments

  1. Martin says:

    I was just starting to ponder whether or not it was possible to scan negatives on my flatbed, now I ponder no longer! Thanks for such a simple solution (mine involved back lights and whatnot)!

  2. steve.mg says:

    SUUUUUWEEET! I will now commence to destroy the available space on my hdd!

  3. steve.mg says:

    Is there a version of this with 120 film? Say yes!

  4. Kathy says:

    Great article, thanks.
    Two questions:
    Will this technique work for colour film as well?
    Do you have a template for medium format negatives?
    Thanks.

  5. Andrew Lewis says:

    To answer some of the questions being asked here – This template will scan medium format film (that’s what I scanned in the article) and yes, it will work for color slides.

  6. Mike Clemens says:

    Neat: I’ve been trying to think of a way to rig something up to handle this. To the poster asking about 120 film: I picked up a sheet of 12×12″ silver paper at the craft store meant for scrapbooking. I eyeballed the above template, and made my own super-size version: the wedge is 3″ wide and 7″ long at the base, which should easily cover a 120/220 frame. Added bonus: the scrapbook paper has a 1/2″ grid printed on the back for easy measuring and cutting.

  7. Pablo says:

    Would it help if the area of reflector over the film was white instead of silver?

  8. Andrew Lewis says:

    It is possible to make this project from white card, but I find silver paper with a tissue paper backing gives better results. I’d encourage you to experiment with both, and see which version works best with your scanner.

  9. Daniel says:

    Couldn’t you use a lightbox above the negative instead?

  10. Martin says:

    I’ve tried using a lightbox, but the results are not great. If you use a florescent bulb (to get the best white) you end up getting a rainbow banding due to the way florescent bulbs work (they aren’t “on” all the time, they flicker very fast). Incandescent bulbs are hard to get a nice clean white from. This is just my experience, let me know if you have more luck.

  11. Ricah says:

    thank you so much for this article! i’ve seen other tutorials like this. but usually involves the use of a backlight.
    i was just wondering if it would work ok to just tape tracing paper to the adaptor to diffuse the light? just a thought.

  12. Andrew Lewis says:

    You can just tape the tracing paper over the open side if you like. I’d recommend just adding it over one half of the opening, so that it doesn’t cut down the light too much.

  13. kombizz says:

    Thank you for sharing this simple and cheap device that could save hundreds dollars by not buying a film scanner.
    I am going to try this method and hopefully, I could scan my entire negatives in my collections.

  14. Alan Robertson says:

    To avoid Newton Rings try taping the negs to thin card and raise them slightly from the glass. Either that or a film holder will work well.

  15. Gill says:

    Thought I’d try this with my admittedly old HP 5100C flatbed scanner. Hopeless results. I don’t seem able to change the scan quality from the 300dpi default. All my scan showed was a dark shape with the tiniest hint of colour on one very small midsection. Any thoughts?

  16. Brian Morgan says:

    One point, the light source is a strip running parallel to the sensor strip, which normally responds to reflected light from the document above. How do you prevent the sensor still seeing the light reflected from the surface of the negative or slide? I still have anti-Newton ring glass plates from my darkroom days.

  17. Brian Morgan says:

    One point, the light source is a strip running parallel to the sensor strip, which normally responds to reflected light from the document above. How do you prevent the sensor still seeing the light reflected from the surface of the negative or slide? I still have anti-Newton ring glass plates from my darkroom days.

  18. Brian Morgan says:

    One point, the light source is a strip running parallel to the sensor strip, which normally responds to reflected light from the document above. How do you prevent the sensor still seeing the light reflected from the surface of the negative or slide? I still have anti-Newton ring glass plates from my darkroom days.

  19. brianmorgan says:

    One point, the light source is a strip running parallel to the sensor strip, which normally responds to reflected light from the document above. How do you prevent the sensor still seeing the light reflected from the surface of the negative or slide? I still have anti-Newton ring glass plates from my darkroom days.

  20. George W. says:

    This is very interesting. Getting a film scanner will surely burn a hole in my wallet. I’ll give this a shot. One question – will using a scanning mask help in any way? I want to be able to scan the sprockets as well. Thank you.

  21. pawowgold says:

    very good, it’s very useful to me, thank you very much!

  22. Nihal Mirza says:

    I scanned hundreds of B/W negatives using an ordinary Epson TX111 flatbed scanner and the results were very good. I placed a clear sheet of glass on the negatives and left the lid open. The best results were obtained during the middle of the day when ambient light was at it’s brightest.

  23. jess says:

    would this work with a hp c4280 all in one ? and if so what settings? i have 35mm color film shot with a holga

  24. Kath says:

    I have negatives of varying sizes, from small to flatbed size negatives. Are there tempates for this for on a regular scanner?

  25. Marco Cevoli says:

    I’ve tried it on a Canon Lide 90 scanner and it didn’t work. The resulting images (from negatives) are completely black. I suppose that the type of light mounted on this scanner aren’t powerful enough.

    1. Vladan says:

      I had the same experience. All I get is black negatives, with image being almost completely non-visible. Perhaps the scanner light is not bright enough?

      1. Mike says:

        I suspect the Canon scanner is a “contact image scanner” instead of a “CCD” imager.
        am not sure of exactly how the former works, but I had a contact image scanner a few years ago, and on it anything that did not contact the plate scanned black (i.e. any creases or the curve at the neck of a book. Also if I remembered its cover pad was dark instead of reflective. Many thin case scanners are supposed to be contact image.You might see if an acquaintance has a CCD type scanner to try. Scanners can be had fairly cheap;y at yard sales and thrift stores on occasion, if you find one that works.

  26. bobchewie says:

    Does this actually work because i was thinking of getting a decent film and flatbed scanner

  27. ze miguel says:

    Did not work at all! It’s shame since I had hope despite being warned about the certainty of not working/producing poor results.

  28. Jorge says:

    Did not work at all. I had better results without the card contraption.

    1. Kath says:

      What did you do?

  29. Kath says:

    Is there anything less complicatead than this? That is already to use, and for the entire flatbed scanner. I have varying sizes of negatives, from real tiny, to reel, to large, and good for negative and positive negatives, and slides and xrays, and so forth?

  30. josé simon says:

    eres un genio. que dios te acompañe siempre mi amigo y hermano

  31. Tom says:

    I noticed that Canon scanners (better: their drivers) detect a negative strip or diapositive and switch to black and white. Even if you surround the negative with colored paper. The paper gets scanned in color and the tiny negative stays black and white. Tested with Mac OS, Canon Lide110.

  32. m00nii says:

    Thank you soooooo much for sharing this idea – worked a treat for me. I’m no photo genius, so found this simple idea fantastic… used the setting you suggested and woop woop huge colour images I can go away and play with… this is going to make a great Christmas treat for members of my family :D

  33. vp says:

    Comparing Methods to Digitize Slides
    http://www.andromeda.com/people/ddyer/photo/slide-transfer.html
    It’s tempting to use a simple attachment to a flatbed scanner to scan slides. This attachment is made by HP and is basically a mirror box which directs light around to the back of the slide, so the scan sees mostly transmitted light instead of reflected light. The mostly is an important consideration; Since lots of light is hitting the slide in the normal reflective path, dust on the near side of the slide or on the scan bed appears as white spots rather than black spots, and white spots are a lot more visible than black. At 1200 dpi, scans seem pretty soft and lack contrast, even after pre-scan adjustment.
    http://www.andromeda.com/people/ddyer/photo/scanners/scanjet-adapter.jpg
    The mirror box looks like a pretty generic design, but it is not. The specifications are precisely tuned to the geometry of the scanner; it doesn’t work even with close family members of the scanner it is designed for.

  34. Harish says:

    Thank you for sharing wonderful idea. I used Epson workforce 545 multifunction scanner. With these instructions I got dark black scans. With little experiment I found that is works with lid open and good ambient light to scan old negative into great pictures. I used photo frame clear glass to hold the negative and standard table lamp to add into ambient light. Thank you.

  35. steven says:

    Andrew my scanner only scans at 300DPI it is a HP scanjet 3300C. Is it possible to increase its DPI to 1200 or not?

  36. steven says:

    Follow up to earlier post. My Scanner only goes to 600 DPI it doesn’t go any higher.

  37. agata says:

    The pictures in the article don’t open :( Is the problem on my side or is there sth wrong with the server?

  38. Anthony Farrar says:

    I made the pyramid and lined it with silver/baking foil – didn’t work.

  39. Chauncey says:

    My fammily members always say that I am wasting my time
    here at net, however I know I am getting knowledge all the time by reading such good articles.

  40. Normally I do not learn post on blogs, but I would like to say that this write-up very pressured me to
    try and do so! Your writing taste has been surprised me.
    Thanks, quite nice post.

  41. What’s up i am kavin, its my first occasion to commenting anywhere, when i read this article i thought i could also make comment due
    to this sensible paragraph.

  42. Prtty nice post. I ust stumbled upon your weblog and wished to
    mention that I’ve really loved browsing your weblog posts.
    After all I’ll bee subscribing for your rss fesed and I’m hoping you write again very soon!

  43. ps4 says:

    Why the Grand Thief Auto has several controversial dilemma is the player of the game themselves.
    The Play – Station 3 posseses an XMB (Cross Media Bar) menu
    system which can be very easy to navigate and one
    in the choices is always to access a web site browser.
    You will only require a computer or even a console that comes with a internet connection and usage
    of a cloud gaming service. She stayed in contact with the Emperor, but
    continued to rebuff his requests.

  44. filnabro says:

    thanks!!!!!!!!!!!!!!!!!

  45. sexy man says:

    Hello there! Do you know if they make any plugins to safeguard against hackers?
    I’m kinda paranoid about losing everything I’ve worked
    hard on. Any tips?

  46. Deepak says:

    Thanks, I will try this out ASAP and let you know about the results.