Project: Shop Hop Project Pouch

Craft & Design Yarncraft

CZ_CraftExclusive.gif
hoptote_main2.jpg
I went on my very first fabric store shop hop last night for some great quilting stores in metro Detroit. Have you ever been on a shop hop before? You buy a “passport” which entitles you to special sales and gifts at each participating store. Knowing I’d be checking out some shops I’d never been to before, I had a feeling I’d be picking up all sorts of good information (AKA lots of flyers and papers). I also wanted to bring some fabric scraps with me so I could get additional yardage that I need, so it quickly occurred to me that I’d need a special pouch to hold all of this in one place in my tote. The Shop Hop Project Pouch was born.


hoptote1.jpg
hoptote_2.jpg
Inside this pouch you’ll have three compartments:

  • 1 large pocket for miscellaneous items
  • 1 small pocket (with Velcro) for a pen or pencil
  • 1 medium pocket for business cards or fabric samples

Start out by measuring and cutting all your fabric. Press the fabric (not the plastic) and set aside. For this pouch you’ll need:

  • 2 pieces of fabric that are 20″ tall and 12″ wide
  • 1 piece of plastic (your choice on the gauge) that’s 7″ x 12″
  • 1 piece of plastic that’s 2″ by 12″
  • 1 piece of plastic that’s 4″ by 12″
  • Velcro (sticky or regular)
  • Any embellishments of your choosing (buttons, trim, etc.)
  • Matching thread for your fabric

hoptote_3.jpg
Once all your pieces are cut, place them on the piece of fabric you want on the inside of the pouch. Take the biggest piece of plastic and pin it at the bottom. You’ll want to pin in each of the four corners as the plastic I used (the thinnest my store had available) tended to move around a lot while working with it.
Take the 2″ piece and pin it above the bottom piece, about two inches higher. Take the last piece and pin toward the top, about 1-2″ (your preference) above the middle piece. Again, pin and make sure they’re secure.
hoptote_4.jpg
Next, sew the plastic pockets on to your fabric. I stayed as close the edge as possible because when we sew the outside fabric to this panel, we want the outside plastic seams to disappear. I eyeballed this and it was about 1/8″.
hoptote_5.jpg
On your final medium pocket, measure 3″ and sew a straight line to accommodate a business card. You can adjust this to whatever width you’d like based on the items you’d like to hold there, but I wanted two spots for cards. My last pocket was a bit wider to hold fabric samples or trim samples.
hoptote_7.jpg
Once you’re done sewing, trim all loose threads. Take your outside panel and place on top of your finished inside panel, right sides together. Pin in place.
hoptote_7a.jpg
Sew the panels together. Leave a five-inch opening at the top to turn right sides out. You want to keep the plastic pocket seams hidden once this is folded inside out, so I found a standard 1/4″ stitch did the trick. However, check your seams and adjust accordingly.
hoptote_6.jpg
Turn the piece right sides out. Turn out all corners and press the piece flat with your hands. Press your top opening and pin shut. Top stitch the entire piece.
hoptote_8.jpg
Sew “fold” lines above the bottom and middle pockets. Fold up your bottom first and see where it naturally falls. Mark this and sew straight across. Do the same for the top flap.
hoptote_main.jpg
You’re all set! I added a piece of sticky Velcro on my pencil pocket and for the main flaps, reinforcing with a button and few stitches. Here are a few more views of the finished piece. I used cotton, but try experimenting with canvas and cotton laminates.
hoptote_unfolded.jpg
hoptote_outer.jpg

10 thoughts on “Project: Shop Hop Project Pouch

  1. Jen @ Brave Little Chicken says:

    I just moved to the Ann Arbor area this week. I haven’t had a chance to scope out any fabric stores in the Southeastern Michigan area. Any suggestions? Thanks!

  2. CaroleM says:

    This is a great idea. I have a shop hop tote I use for all the big stuff, but I like the idea of this for keeping all the small stuff in place.

  3. Lish Dorset says:

    Hi Carole – Thanks! Did you make your shop hop tote?

  4. Lish Dorset says:

    Hi Jen – Welcome! Oh, I’ve got some suggestions ;) For a short drive you can check out Guildcrafters in Berkley. For a longer drive, the Hen House in Charlotte can’t be beat. Lake St. Mercantile(South Lyon) has a huge selection of Moda Fabrics, if you like that brand, too. Over in Brighton, Monarch Quilts has a nice selection and some great classes. I believe several guilds meet there, too.
    Hope this helps!

  5. Colleen says:

    I love the fabric you chose. Can I ask where you got the tree fabric? I’m drooling over it and need to get me some.

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK