Tool Review: BOA Versa Saw

Workshop
Tool Review: BOA Versa Saw

MZ_Toolbox2010.gif

I recently had to pull out my washing machine and remove a section of sheetrock behind it to fix a leak. I took the opportunity, while I had the pipes exposed, to install a drain connection for a laundry sink. To splice in the tee fitting, I had to make two cuts in a long piece of 1.5″ PVC already installed in the wall. This was awkward work—the washer drain is pinched into a corner of the garage, and the pipe itself is jammed up against a stud and only accessible from the side with the sheetrock removed.

Though this type of in-situ pipe cutting can be done with a wire saw (or, in the case of plastic pipe, even just a length of twine), this seemed like a good opportunity to try out the cool restricted-access hacksaw our pals at Garrett-Wade sent me back in March. They actually sell two saws that work on the same principle, both made by UK manufacturer BOA. This one is the “pro” grade unit (which is on sale right now, I should add, for $26.75).

A regular hacksaw frame, of course, is fixed to the blade at both ends. These restricted-access hacksaws, on the other hand, are fixed to the blade only at the back end, closest to the grip, and support the front end using a reciprocating, spring-loaded bar with a thin guide slot and a rubber shoe. The shoe rests up against the workpiece, during the stroke, and the blade moves back and forth through the guide slot, which keeps it from flexing away from the intended cutting path. The upshot is that, unlike a regular hacksaw frame, you can make cuts in stuff with almost zero backside clearance.

The Versa-Saw takes standard 10″ hacksaw blades; they’re mounted in the handle with a single large Phillips-head set screw that indexes with, but doesn’t pass all the way through, the blade’s back mounting pinhole. It ships with a single, pre-installed 24tpi blade that—even taking the short strokes required by the tight clearances—makes very short work of 1.5″ PVC pipe. When starting a cut, I found it helpful to brace the shoe against the workpiece by pushing on the back end of the guide bar with my nondominant hand. The bar is equipped with a rounded pommel, seemingly for this purpose. Once the cut had been started through the pipe wall, it became easier to operate the saw one-handed.

The Versa-Saw is well made; the handle and reciprocating bar are cast aluminum, and it’s all held together with machine screws. The blue rubber grip accents are substantial castings, mounted inside the frame and indexed to protrude through openings here and there, not just glued onto the outside. The reciprocating bar is graduated for depth measurements from 0-5 inches (0-13 cm), and sprung in tension, with a coil spring that rides inside its C-shaped profile. The workpiece shoe/blade guide is made from some kind of black engineering plastic thermoformed around the bar’s business end, with a small blue rubber pad at the very tip.

It’s hard for me to imagine a better tool, for this particular job, than the Versa-Saw. I take great pleasure in those moments, and thus find it generally worthwhile to keep a bunch of odd tools around to meet whatever odd job happens to crop up. On the other hand, it’s probably worth noting that the Versa-Saw sat unused on my bench for months, a solution looking for a problem, before I found a good opportunity to use it.  There are, however, plenty of other applications I can imagine (sawing through a deadbolt from one side of a locked door, for instance), and in many ways the point of keeping a tool like this around is to have it handy for exactly those situations you can’t easily imagine, in advance.

British Hacksaw: BOA Sliding Frame Hacksaw, Moving Frame Hack Saw

8 thoughts on “Tool Review: BOA Versa Saw

  1. David says:

    Neat tool. A video would be nice. In a pinch (pun intended), a plain hacksaw blade can be used in tight places using a pull stroke as in a pruning saw or Japanese carpentry saw.. Release pressure on the return stroke to not kink the blade. Break off the rounded end diagonally for no standoff. Hold with Vice-grips or rag. By-the-by: hacksaws can be used push or pull and pull gives more control. In the day before computers, machinists could do “precision hacksaw” cutting, a seeming oxymoron but now a mostly lost skill.

  2. MAKE | Toolsday on Google Hangout On Air, NOW says:

    […] tool, BTW, is the BOA Versa Saw. Share this: Pin ItLike this:LikeBe the first to like […]

  3. quackquack says:

    I would have just used my hacksaw blade wrapped in duct tape at one end for this. Let the saw do the work and don’t jam it in and no kinks to worry about. Was able to cut a drain pipe off between floor joists where there was just enough room to get my hand around supply lines. If I was a professional plumber and might use it more often I might spend $28 on it, but as the ocassional plumber for just my house I will stick to my $0.25 method.

  4. Toolsday on Google Hangout On Air, NOW says:

    […] Today’s tool, BTW, is the BOA Versa Saw. […]

Comments are closed.

Discuss this article with the rest of the community on our Discord server!
Tagged

I am descended from 5,000 generations of tool-using primates. Also, I went to college and stuff. I am a long-time contributor to MAKE magazine and makezine.com. My work has also appeared in ReadyMade, c't – Magazin für Computertechnik, and The Wall Street Journal.

View more articles by Sean Michael Ragan

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK