3D Printing & Imaging Workshop
Up Mini


Delta Micro Factory / pp3dp.com

Price as tested $899
Print volume 4.7″×4.7″×4.7″
Heated bed? Yes
Print materials ABS, PLA
OS supported Mac, Windows
Print untethered? Yes, after file is sent from computer
Open-source hardware? No
Open-source software? No
Printer control software Up software
Slicing software Up software

Looking like a futuristic kitchen appliance, the $899 Up Mini from Chinese company Delta Micro Factory (PP3DP) is no DIY kit project — it’s designed entirely with the average consumer in mind. It can print compact volumes up to 4.7″×4.7″×4.7″ on a removable perf board, which sits on a heated PCB bed.

Pushbutton-Simple Setup and Software

Setting up this printer is almost as easy as plugging in a microwave and pressing the popcorn button. Just connect the printer and install the Up software from the website; it’s easy to navigate and download the latest version for Mac or PC. Grab the PDF manual while you’re there.
The leveling software does a great job of getting the nozzle and build platform aligned, but be ready to shim the platform as there is a tendency for it to dip at the front left just a touch.

Enclosed for Safety, Cozy for ABS Printing

Up Mini’s enclosed housing helps to reduce the risk of kids (or clumsy people) coming into contact with the heated components during operation. Retaining the heat also helps prevent ABS prints from warping. The enclosure makes the build area a bit smaller, but on the bright side, there’s less worry of software-generated rafts extending off the bed since the nozzle can’t quite travel to the edges of the platform.

Although the printer is enclosed, you can still watch it print. There are two hinged doors, the top one providing a better view during operation. That door also provides filament access — the plastic runs off a spool mounted on an arm in back, then passes over the top of the machine, down through the joint of the top door, and into the print head.

Mostly Quiet Operation

Aside from the obnoxiously loud buzzer that sounds at initialization, print start, and print end, the Up Mini’s housing allows for very quiet operation. The button on the front with blinking indicator light, and the LED work light inside, are well-designed features. The printer operation is similar to its big brother, the Up Plus 2, with the addition of a magnetically removable print head. Although there are no onboard controls, once the print starts you can disconnect the computer.


Extruder Jams

Once the file is sent and the print begins, you can let the Up Mini run unsupervised and you’ll rarely see an “air print” — as long as you’re using their filament. However, over the course of our testing weekend, we experienced at least three filament jams that we weren’t able to diagnose conclusively. It’s possible the problem was with our particular spool of filament, how the filament was being fed into the head, or heat building up inside the housing.

We also had some adhesion issues between layers on our smaller prints (the MAKE robot). Experienced Up Mini users informed us that this was unusual. They also advised that the filament guide at the back of the machine should be avoided and that it’s helpful to print with the top door open, to vent excessive heat in the enclosure.

Solid Objects Printed Best

We printed in ABS; PLA is also possible but experienced users advise adding a fan to cool it. On our first print we had some difficulty removing supports around delicate extrusions and keeping parts intact. However, the Up Mini handled detailed and thin-walled structures well. The calibration cube turned out sharp when using the Fine software setting, and other solid objects printed well, but the Spiral Lightbulb torture print was something of an overhang mess on its last section. We tried it a couple times, always with similar results.

On some occasions, not being able to fully turn off the raft caused unnecessary cleanup. However, the rafts come off cleanly, and the precision of supports is very well calculated.


The Up Mini is an easy-to-use, affordable, complete package. Having the ability to print in ABS gives this little guy the upper hand in its price range.

Primo features

  • Magnetically removable print head makes the extruder almost hot-swappable.
  • Enclosed build platform
  • Great accessory kit, with shears for cleaning prints
  • Compact and sturdy — good for demos and road trips

Who’s It For?

  • Makers
  • Makerspaces
  • Beginners on a budget

Pro Tips

  • The enclosed chamber gets quite warm — if your prints are a little soft, open the lid and door.
  • Reposition the fan as needed to direct more or less cool air on the build.
  • When removing a print, secure the perf board to your workbench and use a palette knife to pop the print up. Then clean up the perf board for next time.
  • The filament guide at the back of the Mini is a bit restrictive. Don’t use it.

Ultimate Guide to 3D Printing 2014This review first appeared in MAKE’s Ultimate Guide to 3D Printing 2014, page 74. Check out the full issue for more!

Tom Burtonwood

Tom Burtonwood is an artist, educator and entrepreneur based in Chicago, IL. Burtonwood co-founded Mimesis, LLC a product development company focused on 3D scanning and digital fabrication. He teaches at The School of the Art Institute of Chicago and Columbia College.

Find Tom on Twitter: @tburtonwood and on Instagram: @tomburtonwood

View more articles by Tom Burtonwood
James Christianson

James Christianson produces video for MAKE and does 3D modeling and animation on the side. He is working with an eight-person team to build a prototype 3D-printed Iron Man suit.

View more articles by James Christianson