101: Upholstery

Craft & Design

upholstry 101 opener.png
101: Upholstery
Add comfort and a fresh new look to your chairs.
By Ashley Jameson Eriksmoen

Dining chairs are an integral part of good times. Where there’s dinner, wine, and company, there are chairs. But old dining chairs are notoriously uncomfortable: no fun for the buns. With simple modifications, though, that can be remedied. Plywood slip seats can be altered to allow for a bit of flex, a tad of padding, and a big difference in comfort. At your next dinner party, don’t be surprised if your guests won’t leave!
This article teaches you the basics of upholstery, and our online supplement at craftzine.com/07/101 includes additional techniques for softening that slip seat. After this project, you’ll be ready to graduate to reupholstering an armchair or a chair with a loose cushion.

Basics

Upholstering with tacks is the most traditional method, and the least expensive for startup costs. You just need an upholsterer’s brass tack hammer with a magnetic tip and tacks. Any stapling described in this article can be accomplished with tacks. Or you can use a pneumatic upholstery staple gun, which is fast, easy on the wrists, and gentle on the fabric.
Not all fabrics are appropriate to use for upholstery. Upholstery fabric should be a weave, never a knit, and should have very little stretch along the grain. It should be sturdy enough to withstand having staples put in and ripped out. Jacquards, brocades, denims, and heavyweight woven wools are all good choices.
A slip seat is a removable upholstered seat that fits into an open chair frame.

Materials

Dining chair with slip seat
Manual screwdriver
Safety glasses
Staple remover or oyster shucker
Tack remover or ripping chisel
Needlenose pliers
Hammer and scissors
Pencil and ruler
Upholsterer’s tack hammer and box of 4oz blue sterilized upholsterer’s tacks
or staple gun and 9″ or 3″ staples
Spray adhesive such as 3M Super 77 or a special foam adhesive, like 3M Foamfast 74 Adhesive
HR 30 polyurethane foam, 24″×48″×1″ thick or similar density natural latex
Polyester batting or cotton wadding, 2/3yd
Fabric, 2/3yd
for seat covering

Directions

Step 1: Prepare your chair.
upholstery figa.png
1a. Check the frame and remove the seat. You want to start with a chair frame that’s in good repair. Check for loose joints and for cracks in the wood. See if the chair is structurally sound by giving it a good wiggle. Turn the chair upside down into a secure position.
upholstery-figb.jpg
Remove only the screws that go straight down to fasten the seat to the frame; leave the horizontal screws on the cross-bracing. Remove the seat, and put the screws in a safe place where you can actually find them later.
upholstery-figc.jpg
1b. Rip and strip. Time to put on your safety glasses: tacks and staples make unpredictable trajectories when you yank on them. If you can’t get ahold of a proper staple remover, an oyster shucker will do the trick. You’ll need to remove all the staples and/or tacks from the seat before you reupholster. This is a tedious chore, but necessary so that the new staples can penetrate the wood.
1c. Check the seat. If the plywood seat pan looks cracked or weak, get a fresh piece of high-grade Europly. The thickness of your seat pan will help to determine whether to make a webbed seat or a slotted seat. (Instructions for these techniques are available at craftzine.com/07/101.)
Step 2: Pad the seat.
upholstery-figd.jpg
2a. Trace your seat onto the foam. Mark another outline ½” beyond the edge of the seat. With the foam on a flat surface, cut along the outer lines. I use an electric turkey slicer that cuts very clean lines in foam, but if it’s 1″ thick or less, sharp scissors work. Cut perpendicularly so the edge of your foam is squared, not beveled. If 1″ of foam isn’t enough, repeat to make a second layer.
upholstery-fige.jpg
2b. Take the seat pan, foam, and spray adhesive to a well-ventilated area. Use spray adhesive to coat the surfaces of the seat pan and the foam. Once it’s tacky, flip the seat onto the foam, which should extend ½” beyond the seat. Put an oversized piece of batting on a flat surface. With your seat foam-side down, center it on top of the batting. Gently lift the batting up to the bottom of the seat, and trim the batting to cover the bottom seat edge, approximately 2″ oversized all around.
Step 3: Cover the seat with fabric.
upholstery-figf.jpg
3a. Fold the fabric in half lengthwise and mark the midpoints of the edges with chalk, or notch them with scissors. Do the same folding the fabric across its width. On the underside of the seat pan, measure and mark the center of the sides, front, and back. Place the fabric on the table right-side down, and center the oversized batting and upside-down seat on top of it. Line up the center marks in the fabric with the center marks on the seat. This is critical if your fabric has stripes or linear patterns.
upholstery-figg.jpg
3b. Gently pull the batting and fabric up around the front edge of the seat pan. Shoot 1 staple or hammer 1 tack to secure the center point of the fabric about ½” to 1″ inside the seat edge. Keeping everything aligned, stretch the fabric across the seat and secure with 1 staple to the center of the back. Pull firmly enough to soften the cut edges of the foam, to create a slight dome, and to ensure there’s no slack in the seat, but don’t overstretch the fabric and cause ripples or divots along the edge. Repeat this at the centers of the sides.
3c. Flip the seat right-side up and take a look. If your fabric is misaligned, you’ll need to pull the staples or tacks and try again. One trick is to put in easy-to-pull “temporary” tacks or staples while you’re placing your fabric. Do this by hammering in your tack only halfway, or by rolling the tip of your staple gun onto one corner, so the staple goes in at a 45° angle, leaving a triangular opening.
upholstery-figh.jpg
3d. If you have a round seat, divide the space between your center point staples, pull the fabric into place, and staple. Split the difference again so that the fabric is evenly distributed around the rim and secured in about 16 spots.
upholstery-figi.jpg
Pull and staple the remaining areas to keep the fabric taut and even all the way around.
upholstery-figj.jpg
Trim the excess fabric about ½” from the staples. If you have a rectangular seat, work your way from the centers toward the corners, pulling the fabric taut as you go. Place staples in a row no more than ¼” apart to create an even edge. Stop about 2″ short of the corners.
upholstery-figk.jpg
3e. Remove any extra bunched-up batting from the corner area. Pull the fabric diagonally across the corner point, and place 1 staple about 1″ in from the edge. On both sides of the corner, turn the remaining fabric at the corner back under itself to form a triangular pleat. Pull that straight over the edge, and finish stapling the fabric down. Trim the excess fabric about ½” in from the staples.
upholstery-figl.jpg
3f. Unless you have notches or welting to complete, you’re almost done. If there are any notches cut into the seat pan to let in the legs, you have some tricky cuts to make. Flip the seat upside down again. Cut the fabric down the center of the notch, stopping about 1″ short of the bottom of the notch. Continue the cut in a Y shape, heading toward the 2 corners of the notch, stopping about ½” short of the actual corners (Figure M). If you cut too deep, it can show on the chair seat.
upholstery-fign.jpg
Yank the triangle of the Y down as tight as you can, and pop a staple into that piece, staying as far from the edge of the fabric as possible so that it won’t fray. You won’t have much room to work, so do the best you can.
Once the triangle piece is secure, yank down the flaps on the sides of the notch and staple them to the walls of the notch. If a rectangular seat has square notches at the corners, instead of cutting a Y, cut a 45° diagonal line toward the corner, again stopping at least ½” short of the actual corner.
upholstery-figo.jpg
3g. Your seat is done. Pop it back onto the chair frame, and screw it back into place. Then take a load off. You deserve it!
upholstery-figp.jpg

Learn More

Webbing: Rough jute upholstery webbing woven in a simple over-and-under pattern will add a lot of give to the seat, making it much more comfortable to sit on.
Slotting: Sometimes the seat is ½” thick or less, and won’t hold up to webbing. You can still give it greater spring by incising slots into the seat.
Welting: This is a roll of matching or contrasting fabric that can hide staples or glue, or can be added to the edge of a slip seat for visual interest.
These techniques are described in detail at craftzine.com/07/101.
About the Author:
Ashley Jameson Eriksmoen teaches upholstery, woodworking, and furniture design at City College of San Francisco, California College of the Arts, College of the Redwoods, and craft centers including Penland School of Crafts in North Carolina and Anderson Ranch Arts Center in Colorado. She designs and builds sculpture and furniture at her studio in Oakland, Calif., and exhibits nationally. ashleyeriksmoen.com

Discuss this article with the rest of the community on our Discord server!
Tagged

I'm a word nerd who loves to geek out on how emerging technology affects the lexicon. I was an editor on the first 40 volumes of MAKE, and I love shining light on the incredible makers in our community. In particular, covering art is my passion — after all, art is the first thing most of us ever made. When not fawning over perfect word choices, I can be found on the nearest mountain, looking for untouched powder fields and ideal alpine lakes.

Contact me at snowgoli@gmail.com or via @snowgoli.

View more articles by Goli Mohammadi

ADVERTISEMENT

Maker Faire Bay Area 2023 - Mare Island, CA

Escape to an island of imagination + innovation as Maker Faire Bay Area returns for its 15th iteration!

Buy Tickets today! SAVE 15% and lock-in your preferred date(s).

FEEDBACK