Find all your DIY electronics in the MakerShed. 3D Printing, Kits, Arduino, Raspberry Pi, Books & more!

Warning: Potentially loud noises ahead. Turn your speakers down if you plan on watching the videos below.

Early testing on the calliope.

Testing the calliope before the crowds show up.

Prior to the recent change of the calendar, I had celebrated eight New Years in NYC. Two of those eight were on the Brooklyn Campus of Pratt Institute to hear a collection of steam whistles toot in the new year. Those were already pretty good odds, but I’ve now celebrated with steam three of nine New Years in NYC. They’re each special in their own right, filled with fond memories. And this most recent one may wind up being very special indeed, if it turns out to be the last time the steam whistles are operated at Pratt.

Begun in 1965 by chief engineer Conrad Milster, the event originally served as a way to justify wanting to hear the steam-powered whistles he collected. Now 77 and having organized the event on his own for nearly five decades, this time last week gossip begin to swirl that this would be Conrad’s final event. There were rumors that Conrad simply wanted to do something else, to relax and enjoy his own new year celebrations. Completely understandable. Then there were also rumors that the administration at Pratt was shutting down the event over liability concerns. And of course there were reports of both of those things being the case.

Weston Voltmeter

With the uncertainty of Dec. 31, 2014, I knew this event was not to be missed. And with everyone from WNYC to Flavorpill saying this was the place to be at the stroke of midnight, I knew it was going to be packed. I made the trip ahead of the crowds in the hopes of getting up close to some of the equipment used. I got more than even I expected with a self-guided tour of the floor of the Engine Room in the East Building!

The view of the Engine Room from the mezzanine.

The view of the Engine Room from the mezzanine.

Whether one hung out on the mezzanine overlooking the generators or got up close to the equipment, there is a lot of beauty in this place. Down to the brass fixtures, copper connections, and patent stamps labeled “88,” “89,” “90″ because you have to remember this facility was built at the end of the 19th century! Oh and cats. Lots of cats. Cats everywhere. Running around the campus, hugging warmth from generators, hanging out on top of pipes. The “Pratt Cats” are equally as famous as Conrad and the steam whistles! Check out the slideshow to see more and if you have a story or info on a specific component or machine, leave a comment below.

Next is a video of the generator in motion. As the evening went on they had to speed up the generator to provide additional steam, to the point where the flywheel was spinning at around 2000-3000 rpm or more!

Several hundred people rung in the new year first with the Conrad’s homemade calliope and then with a selection of whistles from fellow steam aficionados:

And finally here’s a video of Conrad’s 3-bell multi-tone whistle in the daytime to give you an idea of how intense these whistles are:

Update: Late last night my friend and music-maker Norman Savitt uploaded some wonderful ‘behind-the-scenes’ type photos of the steam whistles installation. Big thanks to Norman for use of his photos, and an extra-warm thank you to Conrad and his team for coordinating this unique labor-of-love event.

Nick Normal

I’m an artist & maker. A lifelong biblioholic, and advocate for all-things geekathon. Home is Long Island City, Queens, which I consider the greatest place on Earth. 5-year former Resident of Flux Factory, co-organizer for World Maker Faire (NYC), and blogger all over the net. Howdy!


Related

Comments

  1. biahelvetti says:

    Reblogged this on childoftheisland and commented:
    Oh my! I just HAD to share this! I’m addicted to makezine and me and the boys get loads of ideas from here but this steam whistle is something I’d LOVE to build!!!! What a way to celebrate the New Year!

  2. Last fall, not long after the NY Maker Faire, my wife and I stopped by the Connecticut Antique Machinery Association. We were taking a look at the incredible steam engines in the Industrial Hall of Steam, and we were watching a man working on one of the largest engines in the room. He told us a great story of how the engine was saved from a mill building that was being demolished, and the room it had been in was walled off and forgotten about, only to be discovered again when the wall was knocked down. We talked with him for a good half hour at least, about the history of the engine, and he answered many other questions. The pictures in the article reminded me of that day. When I saw the picture at the bottom of the page – it turns out the engineer who we talked to that day was none other than Conrad himself. I agree that he is a true gentleman.

    1. Nick Normal says:

      That’s a great story Keith! Thanks for sharing.

  3. craqgerbil says:

    wow, were you really there Dec. 31, 2014? What is the secret to time travel?

    1. craqgerbil says:

      wait, never-mind, I read that wrong.