I was first introduced to the wildly talented “wire wrapstress” Dev Khan through my dear friend (and talented artist who shot all the images in this DIY) Sara K. Woll. Sara had commissioned Dev to come over and do a wire wrapping workshop for a crew of us crafty ladies. Dev embodies the true artisan, completely at one with her medium. She cuts and polishes her own stones (as evidenced by her beautifully worked hands) and does some of the most amazing wire wrap jewelry I’ve ever seen. Further, she is all about sharing her love and technique with anyone who is interested. I was thrilled when she wrote this piece for us, which first appeared on the pages of CRAFT Volume 03. Here is the full DIY for you to enjoy.
Setting stones in unique jewelry takes just a few twists of wire.
By Dev Khan
Wire wrapping is an imaginative, spontaneous, and versatile method of setting free-form stones using wire and simple hand tools. It allows the shape of the stone to control the placement of wire. The piece becomes its own tool, the moveable wraps acting as clamps and measuring points. By varying the number of wraps and wires, you can accommodate almost any stone.
Craft a centerpiece for a beading project, create a pendant out of that odd-shaped stone, or turn a beach rock into a magic amulet. Amaze your friends!
A stone at least 1½” in diameter with a flat back
48″ of 24-gauge half-hard square wire sterling silver or gold fill
24″ of 22-gauge half-hard half-round wire sterling silver or gold fill
Chain-nose pliers no teeth
Flush cutter or wire cutter
Note:Tools and wire are available from altasilver.com or riogrande.com.
Step 1: Measure wire for the pendant.
Using square wire, form a loose loop around the stone that is ¾” to 1″ away from the stone all around. Cut at intersection of the loop. Or, using tape measure, find the circumference of the stone, add 3″, and cut.
This is your template for cutting the rest of the wire needed (at least 4 pieces this size) for the wrap. If working with a thicker stone, you’ll need more wires. This group of wires is called the bundle.
Step 2: Wrap the stone.
Cut about 8″ of half-round wire. You’ll make more of these cuts later. Line up the square wire to form a flat sheet. All should curve in the same direction. This inside curve will be the “inside” of your piece.
Making sure the flat side of the half-round is against the bundle of square wire, wrap 5-7 times (or more for a larger stone) around the bundle. This is called the wrap. It should be evenly wound and smooth, and loose enough to slide along the bundle.
Cut loose ends of the half-round wire on inside curve of the bundle. The stone, once placed, will hold these ends in place, preventing them from unwinding. Start next wrap near previous one. This will work as a clamp to hold the bundle wires in line.
Depending on the size and shape of your stone, you will need at least 4 of these wraps. To make wrapping easier, place them close together, and slide them into place later while shaping the wrapped bundle to fit your stone.
Step 3: Shape the wrapped bundle.
Find the bottom center of your stone, and moving the wraps into their proper places, bend the wrapped bundle with your fingers. Check the shape and location of wraps against the stone. Move the wraps to where they will best support the stone. This should be a loose fit with approximately 1″ of room around the piece you are wrapping.
Move the top 2 wraps to meet at the top of the stone. This will form the measuring point for the first bends in forming the bail. The bail is the top of the piece, which allows it to hang on a chain or cord.
Step 4: Close the circle.
After making sure the wrapped bundle is the proper size and shape, place your chain-nose pliers on one of the top wraps, and bend the unwrapped portion 90° upward with your fingers. Repeat on the other side. Gently straighten the loose wires so that the 2 bent sections meet smoothly in the middle. You should now have something that looks like a bubble-blowing wand.
Move one of the wires on the outside edge of the combined bundle and twist it slightly with the pin vise. This will harden the wire, making it stronger to contain the wire bundle without slipping.
Wrap this wire 3 times around the bundle to secure the lower section of the piece, and leave the end uncut for now (you’ll use it to wrap the bottom of the bail). Give these wraps a slight pinch with pliers to tighten them in place.
Step 5: Make the bail.
Determine which side is the front of your piece, and bend the front-most wires down 90° toward the front. These front wires will be used for decorations to be added later. This junction of wires will also be a measuring point for the bail construction. Leave 4 or 5 wires unbent, for the bail.
Step 6: Bend the bail.
With pliers, fan remaining wires into a smooth row of 4 or 5. Place pliers approximately ¾” up from the intersection of wrapped wires, and bend the bail wire forward 90°.
Reposition pliers to other side of first bend, and bend wires downward into a U. Width of the bail top is determined by width of the plier jaws. Place pliers into the junction point formed by the bottom bail wrap. Firmly grasping the sides of the bail, bend the wires upward 90°. This is a hard bend.
Reposition pliers slightly above previous bend and turn wires 90° under. This is a very hard bend, so anchor work firmly between thumb and forefinger. This bend brings all wires roughly parallel to the original bundle of bail wires.
Step 7: Cut the wires.
Clip extra bail wires off where decoration wires are pulled down. The cut wires should run parallel to the back of the bail and tuck above the junction of wires.
Continue wrapping upwards with existing wrap wire, or twist a new one from decoration wires. Wrap tightly to “chin” of bail and clip off — leave no hanging wire. Fan the bail to even out inconsistencies.
Step 8: Set the stone.
With your fingers, bend the wires on the back of the piece inward to form the place where your stone will rest, forming the back of the piece. Place the stone into the setting, and gently bend the wires on the front of the piece to hold the stone in place. The stone will fit very loosely into the setting.
Using pliers, gently turn each wire on the back of the piece to hold the stone tightly in the setting. Be sure pliers are on the square sides of the wire to prevent nicks.
Turn front wires in sequence from the inside of the wrap outwards, always turning in the same direction.
Placement of the next bend is determined by the inside curve of the previous bend.
Step 9: Embellish.
Using the pin vise, twist decoration wires to texture and harden them. With round-nose pliers, turn them into a tiny curl, then use chain-nose pliers to form a spiral at the base of the bail. Decorate using twisted wires, or cut them flush for a clean, tight bail. Use found objects, leftover beads, or seashells to make it your own creation.
About the Author:
Dev Khan loves discovering the edge, bending wire, cutting stones, Burning Man, and archaic German automobiles. It’s the high quirk factor. devkhan.com
20 thoughts on “Flashback: Wire Wrap Jewelry”
Thank you so much for sharing this lovely technique. Very generous.
Dev khan is really a genius in wire n stone art.I am saying it after visiting devkhan.com,where I found a lot of precious ornaments to buy.Thank you for sharing step by step pics of making of a wire wrapped stone(not just a stone with wire after completion). The finished product (in last pic) is looking so much stylish..I love to buy it.
[…]we came across a cool site which you may well take pleasure in. Take a search for those who want[…]
[…]check below, are some totally unrelated sites to ours, on the other hand, they may be most trustworthy sources that we use[…]
[…]very couple of internet websites that transpire to become detailed beneath, from our point of view are undoubtedly effectively worth checking out[…]
[…]here are some links to websites that we link to for the reason that we assume they are really worth visiting[…]
looking for a job online
[…]one of our guests recently proposed the following website[…]
[…]below you?ll uncover the link to some websites that we assume you’ll want to visit[…]
[…]below you?ll find the link to some web pages that we think you’ll want to visit[…]
[…]Here are a number of the websites we recommend for our visitors[…]
i need a ghostwriter
[…]very few internet sites that occur to be in depth beneath, from our point of view are undoubtedly well really worth checking out[…]
neck brace after neck surgery
[…]Sites of interest we’ve a link to[…]
virtual assistant needed
[…]check beneath, are some completely unrelated internet websites to ours, however, they may be most trustworthy sources that we use[…]
Best network company 2015
[…]Here is a superb Weblog You might Find Exciting that we Encourage You[…]
[…]Every as soon as in a when we pick out blogs that we read. Listed beneath would be the most recent web-sites that we pick out […]
[…]usually posts some incredibly interesting stuff like this. If you?re new to this site[…]
craig r myers
[…]please stop by the web-sites we adhere to, which includes this one, as it represents our picks through the web[…]
San Diego motorcycle accident attorney
[…]very handful of websites that transpire to be detailed beneath, from our point of view are undoubtedly effectively worth checking out[…]
dominican republic real estate
[…]please take a look at the web-sites we adhere to, which includes this one, as it represents our picks in the web[…]
computer repairs watsonia
[…]below you will discover the link to some web-sites that we think you must visit[…]
Comments are closed.